arrow_down
  • English
  • Français
  • Deutsch
  • Español
  • Italiano
  • Português
  • 中文
[NA] EXO-R430

FEATURE SUMMARY

NOTE: LINE ART SHOWN IN THIS MANUAL IS FOR REFERENCE ONLY AND MAY VARY FROM ACTUAL PRODUCT.
1. Optical Class 1 Anti-Fog Face shield
Optical Class 1 shield technology features varied thicknesses throughout the lens which enhances visual accuracy, reduces glare, and prevents distortion. Provides 99% protection against harmful UV-A & UV-B rays
2. KwikWick C® LINER FABRIC
Kwikwick C® anti-microbial fabric keeps you cool and dry in warm weather, warm in cool weather Liner is easily removable and washable.
3. KwikFit™
KwikFit™ cheekpads allow easy on and off of the most common styles of eye glasses
4. Ellip-Tec™ II Ratchet System
Easy, Secure, tool-less face shield changes in seconds. Firm detents and smoother function, pulls shield back against the eyeport gasket during closing to ensure a proper seal.
5. Aero-Tuned Ventilation
Five intake ports across the front of helmet forces cool air in while one big exhaust vent maximize movement of hot air out.
6. Face Shield Lock / Vent System
Shield securely locks in place. Or use City Mode for a light air flow when riding at low speeds.
7. Advanced Dual-Density EPS
Advanced multi-layer EPS provides efficient energy displacement in key areas. EPS liner throughout entire chin bar area.
8. Emergency Release System (EMT)
Tabs located under the neck roll allow easy removal of the cheek pads by emergency medical personnel thus allowing easier removal of the helmet.
9. Exocom Link Series Port
Integrated communication port, designed specifically for the EXOCOM LINK series. It does not interfere with other 3rd party com installation.
FACE SHIELD LOCK & REPLACEMENT
RELEASE : Push-in the shield lock button and keep it pushed-in while lifting the shield upward.
warning icon WARNING
DO NOT attempt to adjust while riding.
IMPORTANT NOTE : The face shield can only be removed or installed while in the fully open position. Not doing so will damage the mechanism
REMOVAL
1) Fully open the shield. 2) Push the shield lever upward.
3) With the shield lever up, simultaneously pull the shield upward and away from the shell as shown. Repeat on the opposite side.
INSTALLATION : Push and hold the lever upward. Align the 3 tabs on the shield with the 3 corresponding channels on the baseplate. Press the shield into the baseplate and slightly forward. The shield tabs will “click” into place. Open and close the shield a few times to ensure proper installation.

KWIKWICK® C

CHEEK PADS REMOVAL
Occasionally, cheek pads may need to be removed for washing or replacement.
EMERGENCY (EMT) SAFETY RELEASE SYSTEM
Locate the emergency labelling on the neck roll. Simply reach under neck roll and grab the release strap, pull at a 45 degree angle towards front of helmet. The cheek liner will easily release from the helmet. This system should only be used by trained medical personnel.
CROWN LINER REMOVAL
REMOVAL : Occasionally the crown liner may require removal for washing, replacement or to change sizes.
1) Remove the cheek pads.
2) At the back of the helmet pull the crown liner away from the shell unsnapping the two snaps.
AERO SKIRT REMOVAL
The pliable Aero Skirt was designed to reduce wind from entering behind the face shield area, specifically to keep your face warmer in cold weather.
You do however have the option to remove the Aero Skirt for cleaning or for warmer riding conditions.
REMOVAL : Simply tug on the Aero Skirt and it slides out of the rubber trim channel.
Reverse this process to re-install.

Warranty Info

WARRANTY
All ScorpionExo® helmets have a warranty of 5 years.
Although there is no visible damage on your helmet, general wear and tear over time may affect overall function of protective helmet and increase the risk of injury in accident. It is advisable to replace your helmet no later than every 5 years from purchase.
Should you have a warranty claim, go to your Scorpion dealer with your invoice (this is you purchase proof, it's necessary in order to start the warranty process).
You can find our dealers' list on ScoprionExo websites listed below (choose your country and then the location).
The dealer will contact our after sales service and start the warranty process in order to check and/or repair your helmet.
LIMITATION OF WARRANTY
NO WARRANTIES ARE OFFERED BEYOND THE LIMITED WARRANTY EXPRESSLY SET FORTH IN THIS MANUAL. TO THE FULLEST EXTENT PERMISSIBLEUNDER APPLICABLE LAW, WE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY, OMISSIONS, COMPLETENESS, CURRENTNESS AND DELAYS. IF THESE LIMITATIONS, CONDITIONS, AND OTHER POLICIES INCORPORATED BY REFERENCE ARE HELD TO BE UNENFORCEABLE, OUR LIABILITY FOR DAMAGES SHALL NOT EXCEED THE AMOUNT PAID BY PURCHSER(S) OF SUCH PRODUCT(S)

Other Information

COPYRIGHTS
Copyright © 2020 Kido Sports Co., Ltd. All rights reserved. No part of this guide may be reproduced in any form or by any process whatsoever without prior written consent from the copyright holder.
LICENSES
The ScorpionExo® and the EXO-Com® trademark/logo are exclusively owned by Kido Sports Co., Ltd. Any use of the mark by any other parties without prior written permission of Kido Sports Co., Ltd. constitutes an infringement of legal rights. The Bluetooth® trademark is owned by Bluetooth SIG, and is used under license by BITwave Pte Ltd.
IC/SAR COMPLIANCE STATEMENT

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209.

This equipment should be installed and operated with minimum distance 0 mm between the radiator and your head. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population générale de la norme CNR-102 d'Industrie Canada et a été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209.

Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre tête. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209. Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre tête. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.

FCC/SAR COMPLIANCE STATEMENT

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the Equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 0.919 W/kg.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

CE/SAR COMPLIANCE STATEMENT

This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment.

End user must follow the specific operating instructions for satisfying RF exposure compliance. These requirements set a SAR limit of 2.0 W/kg averaged over one gram of tissue. To meet the above requirement, the device should be placed at least 5mm away from human body in normal use condition.